Leading Power Transformer Manufacturers

Power transformers are crucial for preventing significant energy losses caused by Joule's effect when transmitting large amounts of electrical power across long distances. They do this by turning the power into a high-voltage current and then stepping it down to a low-voltage current, which is safer. As a result, they can frequently be found in industrial facilities, power plants, and electric utility businesses. According to their ranges, power transformers can be categorized as large, medium, or low-power transformers.

• Transformers with medium power might vary from -100MVA.
• Low-power transformers can range in size from 500 to 7,500 kVA.

Components of Power Transformers

The basic components of a power transformer include the core, tap changer, insulating material, and primary and secondary windings.

Core Components

The core is structural support for the windings and a low-reluctance channel for the magnetic flux. Thin steel sheets are laminated and stacked to create them. A covering separates the sheets from one another. The iron or steel sheets are typically less than 1 millimeter thick, and their carbon content is kept below 0.1% to minimize hysteresis and eddy current losses. The eddy current is further diminished by incorporating silicon into the steel alloy. Limbs are the vertical portions of the core where the windings are carried, and yokes are the horizontal portions of the core that join the limbs.

Primary and Secondary Windings

The primary winding is to which the input voltage is applied, and the winding to which the output voltage is supplied is known as the secondary winding. The primary and secondary windings can function as either low-voltage (LV) or high-voltage (HV) winding. Compared to low-voltage winding, high-voltage winding has more turns and is made of a thinner conductor. The low-voltage winding contains fewer turns. Given that the low voltage winding carries a higher current than the high voltage winding, it has a thicker conductor than the high voltage winding.

A specific number of turns of copper or aluminum conductor coil make up the windings. Due to its high electrical conductivity and flexibility, copper is ideal since it requires less winding and is simpler to wrap around the core.

Tap Changer

Tap changers adjust the number of turns in one winding to control the transformer's output voltage as it responds to the fluctuating input voltage and load. The turn ratio is altered as a result of this alteration. The output voltage rises when unloading occurs and falls when the system is loaded. In the HV winding, tap changers are often attached to perform precise voltage adjustments and reduce core losses in the transformer.

Tap changers come in two varieties. On-load tap changers are made to tap the voltage without interfering with the current passage to the load. Offload tap changers need to operate with the transformer's load disconnected.

Bushings

Bushings are sealed barriers that house the terminal connecting the extremities of the transformer windings to the current-carrying cable from an electrical network—usually constructed of porcelain or epoxy resin, bushing insulation. They are usually mounted above the main tank.

The following are additional power transformer components:

• Insulating materials
• Transformer tank
• Conservator component
• Cooling system
• Explosion vent
• Buchholz relay

Power Transformer Operating Principle

The electromagnetic induction law of Faraday is the basis for how power transformers work. All transformers, generators, motors, inductors, and solenoids operate according to this law.

According to Faraday's law, applying a closed loop to a fluctuating magnetic field causes an electromotive force (emf) to be generated across the closed loop. An alternating or fluctuating magnetic flux surrounds a coil when an alternating current is allowed to pass through it in the primary winding. A ferromagnetic core is necessary for the primary winding's magnetic flux to transfer to a secondary winding successfully. Due to electromagnetic induction, the magnetic flux will then cause an emf in the secondary winding. The secondary winding's current will be stimulated by the produced emf.

The induced voltage on the secondary winding can be connected to the input voltage on the primary winding. This is because the voltage for each turn of the primary and secondary windings is the same. The voltage output is lower than the input voltage. When the number of turns on the secondary winding is less than that of the main winding, we have a step-down transformer. The voltage output is greater than the input voltage. If the total number of turns in the secondary coil exceeds that in the primary coil, it is termed a step-up transformer.

Types of Power Transformers

The construction of the core and windings, phases, turns ratio, and core material can all be used to categorize power transformers.

Power transformers based on phases include:

• Autotransformers
• Three-phase transformers
• Single-phase transformer

Power transformers based on turns ratio include:

• Step-up transformer
• Step-down transformer
• Isolation transformer

Power transformers based on core material include:

• Air core transformer
• Iron core transformer
• Toroidal core transformer
• Ferrite core transformer

Choosing the Right Power Transformer Manufacturer

To ensure the most positive outcome when purchasing power transformers from a power transformer manufacturer, it is important to compare several businesses using our directory of power transformer manufacturers. Each power transformer company has a business profile page highlighting their areas of experience and capabilities, along with a contact form to directly communicate with the manufacturer for more information or request a quote. Review each power transformer business website using our patented website previewer for a better idea of what each business specializes in. Then use our simple RFQ form to contact multiple power transformer companies with the same form.